PL-DC Accessories --------------------------------------------- PL-DC12-YM Yoke Mount for PL-DC12 Loudspeaker The Yoke Mount accessory for PL-DC12 shall be a 3.4 mm thick galvanized metal CRS bracket with a 1000h UV and 200 hours salt spray test powder coating. It should provide a traceability identifier. The bracket shall provide two ways to attach the loudspeaker: a slot for quick setup as well as an additional hole when the loudspeaker must be deployed closer to the Yoke Mount. Two round rubber spacers shall be placed between the loudspeaker and the yoke. The Yoke Mount shall have a central 13 mm diameter hole for clamp mounting as well as three sets of fixations accommodating US and European trusses spaced at 240 mm (11 x 7mm oblong), 386.4mm and 589.6mm (7 x 20mm slot) The Yoke Mount for PL-DC12 shall be the Q-SYS PL-DC12-YM. --------------------------------------------- PL-DC8-YM Yoke Mount for PL-DC8 Loudspeaker The Yoke Mount accessory for PL-DC8 shall be a 2.7 mm thick galvanized metal CRS bracket with a 1000h UV and 200 hours salt spray test powder coating. It should provide a traceability identifier. The bracket shall provide two ways to attach the loudspeaker: a slot for quick setup as well as an additional hole when the loudspeaker must be deployed closer to the Yoke Mount. Two round rubber spacers shall be placed between the loudspeaker and the yoke. The Yoke Mount shall have a central 13 mm diameter hole for clamp mounting as well as two sets of fixations accommodating US and European trusses spaced at 240 mm (11 x 7mm oblong) and 386.4mm (7 x 20mm slot). The Yoke Mount for PL-DC8 shall be the Q-SYS PL-DC8-YM. --------------------------------------------- PL-DC26-YM Yoke Mount for PL-DC26 Loudspeaker The Yoke Mount accessory for PL-DC26 shall be a 2.7 mm thick galvanized metal CRS bracket with a 1000h UV and 200 hours salt spray test powder coating. It should provide a traceability identifier. The bracket shall provide two ways to attach the loudspeaker: a slot for quick setup as well as an additional hole when the loudspeaker must be deployed closer to the Yoke Mount. Two round rubber spacers shall be placed between the loudspeaker and the yoke. The Yoke Mount shall have a central 13 mm diameter hole for clamp mounting as well as two sets of fixations accommodating US and European trusses spaced at 240 mm (11 x 7mm oblong) and 386.4mm (7 x 20mm slot). The Yoke Mount for PL-DC26 shall be the Q-SYS PL-DC26-YM. --------------------------------------------- PL-DC24-YM Yoke Mount for PL-DC24 Loudspeaker The Yoke Mount accessory for PL-DC24 shall be a 2 mm thick galvanized metal CRS bracket with a 1000h UV and 200 hours salt spray test powder coating. It should provide a traceability identifier. The bracket shall provide two ways to attach the loudspeaker: a slot for quick setup as well has a additional hole when the loudspeaker must be deployed closer to the Yoke Mount. Two round rubber spacers shall be placed between the loudspeaker and the yoke. The Yoke Mount shall have a central 13 mm diameter hole for clamp mounting as well as two sets of fixations one spaced at 240 mm (10.5 x 7mm oblong) and the other being 4 x 8.5 mm holes spaced at 308 mm. The Yoke Mount for PL-DC24 shall be the Q-SYS PL-DC24-YM. --------------------------------------------- PL-DC26-FM Flush Mount for PL-DC26 Loudspeaker The accessory allowing surface mounting of the PL-DC26 shall built with three 1.5 mm thick galvanized metal CRS brackets with a 1000h UV and 200 hours salt spray test powder coating. Each part should provide a traceability identifier. A bracket shall be attached to the loudspeaker top, bottom or back using the 4-hole pattern (4 x 2.25 pitch, M6) while the other brackets shall be installed on the surface where the loudspeaker shall be mounted. Angles between those brackets can be indexed in 10° steps. Attachments between the loudspeaker and the wall brackets shall be done with keyholes and a single fastener. The Flush Mount for PL-DC26 shall be the Q-SYS PL-DC26-FM. --------------------------------------------- PL-DC24-FM Flush Mount for PL-DC24 Loudspeaker The accessory allowing surface mounting of the PL-DC24 shall built with three 1.5 mm thick galvanized metal CRS brackets with a 1000h UV and 200 hours salt spray test powder coating. Each part should provide a traceability identifier. A bracket shall be attached to the loudspeaker top, bottom or back using the 2-hole pattern (60 mm or 70 mm, M6) while the other brackets shall be installed on the surface where the loudspeaker shall be mounted. Angles between those brackets can be indexed in 10° steps. Attachments between the loudspeaker and the wall brackets shall be done with keyholes and a single fastener. The Flush Mount for PL-DC24 shall be the Q-SYS PL-DC24-FM.